Showing results: 3211 - 3225 of 4352 items found.
-
LS9923 -
Lisun Electronics Inc.
LS9923 programmable withstanding voltage & insulation test system is high-performance testing device special for AC&DC Withstanding Voltage and Insulation Resistance Test, It allows setting the output voltage. The warning value,testing time and some other parameters can be set in the screen.It with a variety of automatic test functions. The testing is quick and high accuracy which is not only applied in the production line but also in the develop research.
-
1105 ER -
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● In addition to facilitating for precision measurement, test leads for simplified two-wire measuring system also are supplied as standard accessories.● Battery operated.● Battery life indicator. ● Calibration performed with supplied test leads.
-
4105 ER -
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● In addition to facilitating for precision measurement, test leads for simplified two-wire measuring system also are supplied as standard accessories.● Battery operated.● Battery life indicator. ● Calibration performed with supplied test leads.
-
2105 ER -
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● In addition to facilitating for precision measurement, test leads for simplified two-wire measuring system also are supplied as standard accessories.● Battery operated.● Battery life indicator. ● Calibration performed with supplied test leads.
-
2120 ER -
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● 0Ω adjustment.● Battery operated.● Data hold function.● Low battery indication.● Calibration performed with supplied test leads.
-
2705 ER -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Battery check function.● Calibration performed with supplied test leads.
-
NGY 10GE SFP+ and 10G BASE-T Load Modules -
Keysight Network Applications and Security
Ixia's 10 Gigabit Ethernet LSM10GXM test load modules delivers an industry-leading, high-density, affordable layer 2 through 7, 10 Gigabit Ethernet IP test solution. The NGY family supports both low port count layer 2/3 applications with limited project budgets and highest density test lab, QA, and system test applications. NGY is perfect for both converged data center infrastructure testing and 10GbE switch test beds. NGY load modules leverage Ixia's converged data center test applications to offer the high port scalability, virtual scalability, protocol coverage, with an affordable test solution for data communications testing.
-
National Technical Systems
Gravelometer testing is designed to evaluate the resistance of vehicle surface coatings (paint, clear coats, metallic plating, etc.) to chipping caused by the impacts of gravel and other flying objects in accordance with SAE and ASTM standards. The primary usage of this test is to simulate the effects of the impact of gravel or other debris on automotive parts. Test samples are typically mounted in the back of the Gravelometer, and air pressure is used to project 1 pint (approximately 300 pieces) of gravel at the sample. The test sample is then removed and gently wiped off with a clean cloth. Tape is then applied to the entire tested surface. Removal of the tape then pulls off any loose fragments of the coating. The appearance of the tested sample is then compared to standard transparencies supplied by SAE to determine the chipping ratings. Visual examination can also be used to describe where in the coating/substrate system that the failure has been induced.
-
Silicon Control Inc.
The PCIE850 provides a complete test and debug solution for PCI Express Bus. Interposers and probes connect to the PCIE850 providing access to PCI Card, AMX, XMC and VPX systems.
-
S100A -
Ponovo Power Co., Ltd.
S100A is the Universal Single Phase Protection Relay Test Set with 1*100A and 3*150V output, local control system for basic relay testing with manual operation.
-
HVST -
Test Electronics
The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. This voltage is displayed on an oscilloscope and recorded on the Pass/ Fail LED latch monitor. This voltage will be accurate despite the impedance of the winding being tested. The insulation system can be tested way above the operating voltage because of the brief duration of the applied voltage test pulse. This allows faults to be detected long before they become apparent at operating conditions.
-
MOTOMEA
*The performance data of electric motors, in the majority of all cases, is performed by a brake test. Power input is calculated from current and voltage. Torque and power output are measured with a brake. It is important to reach, for each point, a persistent temperature. In case of large outer rotor BLDC motors, which are usually used for electric scooters, this traditional procedure may take many hours to complete, and is very complicated. *For several years, an innovative motor tester of MEA Testing Systems Ltd. is on the market. This testing system avoids any temperature confusion by testing a motor at constant temperature over the entire speed range. The test procedure is very fast, and gives the full load performances, including PWM current, voltage, torque, and driver efficiency, from stall up to no load. *During the test procedure, the motor is freely accelerated from stall to no load speed. The load of the motor is only the predetermined inertia of the rotor. From the moment of inertia and the acceleration, the torque of the motor is calculated and, also, the power output over the whole speed is given. Since the entire measuring time, depending on the motor size, is usually less than one second, the motor has no time to warm up. It remains at room temperature.
-
JTAG Technologies Inc.
Want to improve the overall test coverage of your assembled boards? It’s easy. Simply combine or integrate your JTAG Technologies boundary-scan tools with your existing automatic test equipment (ATE). We work with any vendor of in-circuit testers (ICT), flying probes (FPT) or functional testers (FT).We offer solutions for most of the available automatic test equipment systems, in addition we can support you with customized integrations for your existing automatic test equipment (ATE).
-
PXIe-1149.1/4E -
Corelis, Inc.
The PXIe-1149.1/4E is a highperformance, multi-feature boundaryscan controller for multi-TAP and concurrent JTAG test and in-system programming. Featuring a high-speed PXI Express (PXIe) interface with four independent and configurable Test Access Ports (TAPs) along with direct serial programming capability, the PXIe- 1149.1/4E enables of boundary-scan integration with PXIe systems.
-
PTFM-1000V2 -
HORIBA, Ltd.
The Pitot Tube Flow Meter, PTFM-1000V2 is a standalone interface for measuring exhaust gas flow rate of combustion engines. The system uses the tried-and-tested pitot tube principle with high-frequency transducers to accurately measure highly pulsating exhaust flows with a sampling rate of 1kHz. This rapid capture rate ensures that any pulsations or exotic behaviour in an engine is measured, and the unique design of the PTFM pitot tube means reverse flows can be measured with the same guarantee of sensitivity. The interface can be run standalone with a laptop, or seamlessly integrated to run alongside an analyser system without adding any more steps to the test cycle process.
